Loctite EA 934NA AERO Two parts Epoxy paste adhesive 1 kit

LOCTITE EA 934NA AERO is a two-component thixotropic paste adhesive, which cures at room temperature and possesses superior strength to 149°C and higher. 

• Pack size: 1 kit (A and B components)

Application

• Its thixotropic nature and good compressive strength make it ideal for potting, filling and fairing, as well as for shim applications.
• Mixing – Combine Part A and Part B in the correct ratio and mix thoroughly. THIS IS IMPORTANT! Heat buildup during or after mixing is normal. Do not mix quantities greater than 1 pound as dangerous heat buildup can occur causing uncontrolled decomposition of the mixed adhesive. TOXIC FUMES CAN OCCUR, RESULTING IN PERSONAL INJURY. Mixing smaller quantities will minimize the heat buildup.
• Applying – Bonding surfaces should be clean, dry and properly prepared. For optimum surface preparation consult the LOCTITE Surface Preparation Guide. The bonded parts should be held in contact until the adhesive is set. Handling strength for this adhesive will occur in 8 hours @ 77°F/25°C, after which the support tooling or pressure used during cure may be removed. (Alternates are: 20 minutes @ 140°F/60°C, or 1 minute @ 205°F/96°C.) Since full bond strength has not yet been attained, load application should be small at this time.
• Curing – This adhesive may be cured for 5 to 7 days @ 77°F/25°C to achieve normal performance. Accelerated cures up to 200°F/93°C (for small masses only) may be used as an alternative. For example, 1 hour @ 200°F/93°C will give complete cure.
• Cleanup – It is important to remove excess adhesive from the work area and application equipment before it hardens. Denatured alcohol and many common industrial solvents are suitable for removing uncured adhesive. Consult your supplier’s information pertaining to the safe and proper use of solvents.

Characteristics 

• Room Temperature Cure
• Good Gap Filler
• 149°C / 300°F Performance
• Potting Material
• MMM-A-132 Qualified
• Develops Strength Rapidly

Technical specifications

Hazard statements (CLP) – A part

Signal word: Warning

Hazard Statements (H-phrases)

• H315: Causes skin irritation.
• H317: May cause an allergic skin reaction.
• H319: Causes serious eye irritation.
• H341: Suspected of causing genetic defects.
• H373: May cause damage to organs through prolonged or repeated exposure.
• H411: Toxic to aquatic life with long lasting effects.

Precautionary Statements (P-phrases)

Prevention:

• P273: Avoid release to the environment.
• P280: Wear protective gloves/protective clothing.

Response:

• P302+P352: IF ON SKIN: Wash with plenty of water and soap.
• P333+P313: If skin irritation or rash occurs: Get medical advice/attention.
• P337+P313: If eye irritation persists: Get medical advice/attention.

Hazard Information (CLP) – B part

Signal word: Danger

Hazard Statements (H-phrases)

• H314: Causes severe skin burns and eye damage.
• H317: May cause an allergic skin reaction.
• H331: Toxic if inhaled.
• H411: Toxic to aquatic life with long lasting effects.

Precautionary Statements (P-phrases)

Prevention:

• P261: Avoid breathing vapour.
• P273: Avoid release to the environment.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.

Response:

• P303+P361+P353: IF ON SKIN (or hair): Remove immediately all contaminated clothing. Rinse skin with water/shower.
• P304+P340: IF INHALED: Remove person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P310: Immediately call a POISON CENTER/doctor.
• P333+P313: If skin irritation or rash occurs: Get medical advice/attention.

Henkel AG & Co. KGaA, Henkelstr. 67, 40589 Düsseldorf, GERMANY, +49 211 7970, [email protected], www.henkel.com